login   |    register
Plus Model [ MORE REVIEWS ] [ WEB SITE ] [ NEW STORIES ]

Built Review
148
Multicar M-22
Plus Model 1/48 Multicar M-22
  • move

by: Blazey [ ONKOS1 ]


Originally published on:
Armorama

introduction
The Multicar M-22 was produced in East Germany between 1964 and 1974, and in total 42500 vehicles were made. There were ten versions installed on the basic chassis. Construction was simple, reliable and easy to maintain. Because of its versatility it was used by most of the Warsaw Pact armies and civilian operators.

Contents
The kit is packed in a small cardboard box. The box contains two bags of resin parts, a bag with copper wire, clear film for the windows, a photo-etch fret, a set of decals with a correction set for Czech vehicles, and obviously instructions.

Build & Review
At first glance the elements look very good. All are very carefully cast.

The construction begins with the assembly of elements of the rear suspension. All the parts fits well - there are even pin holes to locate the parts. Next we carry on adding the rear axle and drive shaft. I must admit I had a small problem finding the right angle to connect and fit those elements together, simply because the end parts of what should be a drive shaft(made from wire) are straight, and in the real vehicle the shaft angles from the gearbox towards a rear axe. In the end I replaced the copper wire with a piece of styrene and glued all the parts together. The fit is far from good but it will be invisible once the model is complete.

Next step is the front suspension and exhaust. Front suspension went on very well. More problems were found with the exhaust. It contains of three elements: a silencer made of resin and the pipes made of copper wire. Once again, I had to replace the copper wire and resin part (which wasn't included it the kit) with the pieces of styrene.

After fitting all the parts of suspension we are told to install the wheels.
The wheels - Wow! They are a work of art. Perfectly moulded with a lots of details and a tiny beautiful thread - Amazing. I can say they are the really high of this kit.

The next step is a cabin. The bottom part is one piece of cast resin, into which we have to fit the side panel with a lever for a handbrake, pedals made of photo-etch parts, and a very simple dashboard. The dashboard is simple because in the real vehicle it was also very, very simple. I must say that all the elements that should be on it are there. Once the dashboard is in place, we have to add the driver seat and the steering wheel with its shaft made of wire. In the end we glue it to the frame, and finish assembling the rest of the parts mounted onto the frame.

All the mudguards fit well. Same with the battery and a spare wheel. What caused a problem was the part for a hydraulic shaft that raises the bed. It was cast very badly and I had to replace it with a simplified part made of styrene.

Assembling the bed was very easy since all the parts were cast straight. A cherry on the cake are tiny hinges made of photo-etch, which add nice detail to it.

Once we have all the lights in place (made of clear parts) we can start the fight with the upper part of the cabin. It's a one-piece casting, and very careful cutting is required to get rid of all the flash. My advice is to do it with a fresh sharp blade. When this is done we need to add a tiny door frame to it and wipers - both made of photo-etch, and the windows are cut from the film.

Decals allow us to make one civilian vehicle and two army vehicles - one from the Czechoslovak People's Army and another of the German Democratic Republic National People's Army.

Conclusion
The subject and the scale allows us to make a nice diorama with any plane used by the countries from Warsaw Pact, or simply a civilian vehicle. Weaknesses include the use of copper wire for the shafts and pipe elements small piece of styrene would be much better.

Over all this is a nice and original kit of a vehicle used widely by Warsaw Pact countries - it will fit perfectly with a Mig-21. Not recommended for beginners as some parts are difficult to assemble, but a pleasure to build.
SUMMARY
Highs: The subject ,and the scale. Which allows to make a nice diorama with any plane used by the countries from Warsaw Pact, or simply a civilian vehicle.
Lows: Copper wire for the shafts and pipe elements small piece of styrene would be much better.
Verdict: A nice and original kit of the vehicle used widely by Warsaw Pact countries. Will fit perfectly with Mig-21. Not for beginners as some parts are difficult to assemble, but a pleasure to build.
Percentage Rating
87%
  Scale: 1:48
  Mfg. ID: 4048
  Suggested Retail: 27.30 EUR
  Related Link: 
  PUBLISHED: Jan 15, 2017
  NATIONALITY: Czech Republic
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 87.33%
  MAKER/PUBLISHER: 85.48%

Our Thanks to Plus Model!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.
View Vendor Homepage  More Reviews  

About Blazey (Onkos1)
FROM: ENGLAND - EAST ANGLIA, UNITED KINGDOM

Copyright 2017 text by Blazey [ ONKOS1 ]. All rights reserved.


Reader Reviews
Do you own this item and want to review it? You can add your review of the item here. Please read the reader review instructions before posting.


Comments

Ah, another proudly-produced automotive offering from the former Soviet-occupied DDR, home of the Trabbi!
JAN 16, 2017 - 11:35 AM
Tip: Just hit enter to submit your reply!
   

What's Your Opinion?


Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move